Latest Update: 18/08/2020
The below log shows all updates for this product since release:
v2.6
- Installer updated for P3D v5
- No smoking and seatbelt chime added
- Trim wheel and indicator now animates full range up to 20 degrees
v2.5
New Features:
- Added click spots to close pilot door and cabin door for all models.
Bugs & Updates:
- Pilot door door handle click spot now working for the GNS/RDR model.
- All gauge lights and bulb lights are off when no battery power is available.
v2.4a
BUGS & UPDATES
- Pitch stability was increased as we found it was a bit sloppy during approach for landing.
v2.4
New Features
- L R fuel flow warning lights now extinguish at around 1,200 RPM or 38 PSI hydraulic pressure.
- ASI reference card updated for new "Airpeed Limitations Table". (Check Kneeboard)
- ASI background card texture updated to match new "Airspeed Indicator Table".
- Attitude gauge updated with outer card now banks and upper pointer is now static.
- Any door open now shows on annunciator warning light.
- Ram air knob added for fresh air.
- Gear warning for theses conditions: 1) Throttle below 20 percent with gear up. 2) Flaps 30 and beyond with gear up.
- Bugs & Updates
- G load tolerance updated for new pitch control.
- Auto start causes left fuel tank selector to go to all tanks and gets stuck. Fixed.
Flight Dynamics
- Pitch and Rudder control improved for realism.
- Pitch stability improved for realism.
- Major overhaul on the engine for accurate engine performance.
v2.3a
New Features
- PRODUCT INSTALLER NOW INCLUDES A P3D V4 INSTALLATION OPTION WITH NEW 64BIT DLL'S.
- REPAIR AND REFUEL NOW HAS SOUND.
- AUTOPILOT NOW CAN CHOOSE BETWEEN NAV1 AND NAV2 FREQUENCY FOR THE NAVIGATION SOURCE.
- VOR/LOC MODE AND THE GS MODE ARE NOW SPERATE BUTTONS AND MODES.
Bugs & Updates
- AIRCRAFT TITLE NAME UPDATED FOR FSX & P3D.
- ANNUNCIATOR LIGHTS AND OTHER DECAL LIGHTS ARE NOW BRIGHT WITH MAIN PANEL LIGHTS OFF.
- OUR LATEST GNS530 GPS UNIT IS INCLUDED.
v2.3
New Features
PRODUCT INSTALLER NOW INCLUDES A P3D V4 INSTALLATION OPTION WITH NEW 64BIT DLL'S.
Bugs & Updates
- AIRCRAFT TITLE NAME UPDATED FOR FSX & P3D.
v2.2
New Features:
- Flight director visibility removed and new animation added Attitude gauge now can be caged Attitude gauge has a new tooltip Wheel chocks can only show if the parking brake is on when selecting the option Added a upper lubber line to the OBI gauge texture
Bugs & Updates:
- Flight Director bank is fixed and now guides you through a turn EGT updated for accuracy Vibration with parking brake on fixed Autopilot localizer and approach mode fixed Upper bank pointer reversed animation fixed Cabin pressure knob no longer will get stuck Attitude pitch and bank degrees updated for accuracy P3D model name will now show GTN or GNS version when selecting Right engine start button tooltip now says right engine Turn indicator flag now fixed and only needs battery power
v2.1a
- The GTN 750 config file was corrupted and will not update from the config tool.
- We also created instructions for when using the GTN 750 config tool with our products.
v2.1
New Features:
- Updated installer with option to install 1 GTN 750 unit or dual GTN 750 units Updated installer with new features and better information The GTN 750 3D unit now have a click spot for the SD-Card The GTN 750 units now comes pre configured with sound on and naviagetion pre-set Added new hotspot for radar to open to 2D panel
Bugs & Updates:
- Brightness issue for the GTN 750 fixed
- Removed com/nav 2 radio unit from the DUAL GTN 750 panel Removed click sounds from the course and decision height knobs Radar options updated with new instructions in PDF format Turn Coordinator updated for accuracy
Flight Dynamics:
- Pitch, yaw and roll performance updated
v2.0
- ADF mode must be on for the signal to be active
- Nav 1 tooltip removed from Nav 2 radio
- LCD screen
- Main and passenger door handles fixed for function from interior model
- New integrated WX Advantage Radar by Rex / Milviz (Captain Sim / ASNRadar instructions now include Reality's WX 500)
The product download in your account is updated as and when updates are released, so if purchasing after any of the given dates your product will include all updates prior to that date.
To download updates you will need to re-download the product from the 'Your Orders' section of your account which you can log into by clicking here.
For guidance on downloading this update, please visit this FAQ.